[{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/988/original/20251008_1559_Wiring_Complexity_Chaos_remix_01k7254p76f8vrjy02wsbpk3cw2.png?1760573659","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eWipperSnapper is a firmware (Arduino sketch) that connects boards with Components + Sensors in a no-code way. It's meant to be easy for beginners to start making things online quickly and simply, but sometimes \u003cstrong\u003ewe forget how much knowledge is expected\u003c/strong\u003e.\u003c/p\u003e\n\u003cp\u003eIt can be a tall order to know how to find the pin names for each board, but doubly so when you want to connect a seemingly easily sandwiched FeatherWing into the mix.\u003c/p\u003e\n\u003cp\u003eToday I followed this journey to test a newly supported E-ink FeatherWing display with one of our older boards, the Feather ESP32 v2 (Huzzah32), to replicate the MagTag setup which we know works well.\u003c/p\u003e\n\u003cp\u003eAs I looked for the documentation link in the New Components dialog, I realised this was a step too far for many people to take confidently alone and I should probably document the journey.\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003ch2\u003eBreaking it down\u003c/h2\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eIt's a few steps to confidence, but mainly it's a few implicit steps and a couple of explicit ones:\u003c/p\u003e\n\u003col\u003e\n\u003cli\u003eUse \u003cstrong\u003eNew Device\u003c/strong\u003e button on \u003ca href=\"https://io.adafruit.com/\" target=\"_blank\"\u003eio.adafruit.com\u003c/a\u003e to install WipperSnapper\n\u003col\u003e\n\u003cli\u003eFollow all steps, use a Chromium based browser for Web Installer\u003c/li\u003e\n\u003cli\u003eOnce secrets are on the board and it's rebooted and you've been asked to name it then it should be online.\u003c/li\u003e\n\u003c/ol\u003e\n\u003c/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFind your Main boards pins\u003c/strong\u003e (or use Docs link from IO Devices page)\n\u003col\u003e\n\u003cli\u003eLocate the invoice/order and find the product name/id to then find the product webpage\u003c/li\u003e\n\u003cli\u003eGoto the adafruit site and locate the same product page in the shop - confirm the info matches\u003c/li\u003e\n\u003cli\u003eScroll down the product page to the Learn Guides section, and the first is product learn guide.\u003c/li\u003e\n\u003cli\u003eEach Product Learn guide has a pinout page (search learn.adafruit.com or use product page link)\u003c/li\u003e\n\u003cli\u003eThe pinout page has sections, dedicated to functionality / peripherals, with the main images at the top and highlighted versions throughout, so you might need to read relevant bits first then go back through the lot to catch any useful pointers (or at least keep referring back).\u003c/li\u003e\n\u003c/ol\u003e\n\u003c/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFind your \"Component\"'s pinout\u003c/strong\u003e (e.g. a featherwing or sensor or button or neopixel strip)\n\u003col\u003e\n\u003cli\u003eWhile you can follow the previous steps, especially if it's something adafruit don't sell (maybe find a similar one Adafruit \u003cem\u003edoes sell\u003c/em\u003e and read that product learn guide to gain confidence), \u003cem\u003e\u003cstrong\u003eit's easier \u003c/strong\u003e\u003c/em\u003e\u003cstrong\u003eto use the \u003cspan style=\"text-decoration: underline;\"\u003eNew Component\u003c/span\u003e dialog from the WipperSnapper device page on Adafruit IO\u003c/strong\u003e\u003cem\u003e\u003cstrong\u003e,\u003c/strong\u003e \u003c/em\u003ewhich has Documentation links for all components\u003cem\u003e.\u003c/em\u003e\n\u003c/li\u003e\n\u003c/ol\u003e\n\u003c/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCreate the component on WipperSnapper\u003c/strong\u003e and \u003cstrong\u003eselect the correct Pins\u003c/strong\u003e (sometimes automatic)...\n\u003col\u003e\n\u003cli\u003eStart matching up the pins you've connected together physically, and if it's a featherwing (all pins connected physically) then use the product learn guide for the featherwing to establish which functions you intend to use and therefore which physical pins on the pinout page will be used.\u003c/li\u003e\n\u003cli\u003eSelect the New Component from list (in New Component Dialog), and continue to the Create Component page, where you select the pins and configuration options before clicking Create Component.\u003c/li\u003e\n\u003cli\u003eThe new component should be created and start reporting data, or be ready for you to send it some (like a colour for NeoPixels/DotStars, or some text for a Display). Test it\u003c/li\u003e\n\u003c/ol\u003e\n\u003c/li\u003e\n\u003cli\u003eRejoice, then think about creating an Action that uses your data or sends some weather info to a display.\u003c/li\u003e\n\u003c/ol\u003e\n      \n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003ch2\u003eMy Example:\u0026nbsp; Feather ESP32 V2 (Huzzah32) mounted to the 2.9\" E-Ink Featherwing\u003c/h2\u003e\n\u003ch3\u003eStage 1 + 2, Install, get board online, then find pinout page\u003c/h3\u003e\n\u003cp\u003e\u003ca href=\"https://io.adafruit.com/devices/new\" target=\"_blank\"\u003eInstall WipperSnapper\u003c/a\u003e then use the docs link from device page, followed by selecting the pinout page.\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/970/original/image.png?1759930769","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eOr find learn guide via product page:\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/971/original/chrome_Bz8dkCyNUV-ezgif.com-optimize.gif?1759931122","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eRead the pinout page, notice the nice SVG Pretty-Pins diagram near the top, and then read anything you feel relevant, in this case I'm connecting an SPI (MOSI/MISO/CS) screen, but you wouldn't know that yet necessarily, so just keep the page open for later.\u003c/p\u003e\n\u003cp\u003eNormally the board will have silk screen labels identifying the pins, but naming systems vary so use the Pretty Pins diagram as a good way to find the other labels. The Top and Bottom images of the board are also useful if yours is hidden while attached to a featherwing or embedded in a project.\u003c/p\u003e\n\u003cp\u003eStage 2 Complete - Yay!\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003ch3\u003eStage 3 - Find pinout for your component\u003c/h3\u003e\n\u003cp\u003eUse the New Component button from your WipperSnapper Device page, then search for the component to add (or a similar compatible sounding one), before using the Docs link in the component results.\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/972/original/image.png?1759931709","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/973/original/image.png?1759931741","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eNow visit the Pinouts page on the learn guide or read the datasheet if that is linked instead.\u003c/p\u003e\n\u003cp\u003eFor my featherwing, there are a few models covered in the same page, so I ended up at this section: \u003ca href=\"https://learn.adafruit.com/adafruit-2-9-eink-display-breakouts-and-featherwings/pinouts#featherwing-connections-3102326\" target=\"_blank\"\u003ehttps://learn.adafruit.com/adafruit-2-9-eink-display-breakouts-and-featherwings/pinouts#featherwing-connections-3102326\u003c/a\u003e\u003c/p\u003e\n\u003cp\u003ePinout located - Stage 3 Complete!\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"text","content":"\n        \u003ch3\u003eStage 4 - Linking the pins together mentally and virtually\u003c/h3\u003e\n\u003cp\u003eYour pins are probably already connected, you eager beaver, but if not that's fine too. Even if they are,\u0026nbsp;\u003cspan style=\"text-decoration: underline;\"\u003edouble check the pins are capable of what you think and at the expected voltage levels\u003c/span\u003e. \u003cbr\u003eCountless hours are wasted by using a pin that you think is \"fine\"/normal, and then turns out to be already in use for some documented purpose, or is not compatible (voltage/features) like a boosted 5volt output pin (D5 on itsybitsy).\u003c/p\u003e\n\u003cp\u003eConfirm the needed functionality (and therefore pins) on the components pinout page.\u003c/p\u003e\n\u003cp\u003eWhat does that mean? Well, are you connecting using one of two busses (data connnection types), either SPI or I2C, or maybe you want the buttons and display to be used on the same featherwing (like I do).\u0026nbsp;\u003c/p\u003e\n\u003cp\u003eYou'll need to ensure all the required pins are connected, and later in the Create Component dialog select those correctly. Optional pins are...optional, \u003cem\u003esurprise!\u003c/em\u003e\u003c/p\u003e\n\u003cp\u003eLets break it down:\u003c/p\u003e\n\u003cp\u003e4.1. Check the first functionality you care about (do one at a time, but they will probably share pins), so Display in this case.\u003c/p\u003e\n\u003cp\u003e4.1.1 View the highlighted pinout image and then compare with the pinouts for your main board, noting which is called which from the Main boards perspective.\u003c/p\u003e\n      ","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/974/original/image.png?1759932471","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/975/original/image.png?1759932583","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eNow with SPI, you normally don't get much choice about the main SPI pins [SCK and MOSI/MISO or \u003cspan\u003ePICO (Peripheral In, Controller Out) and POCI (Peripheral Out, Controller In)]\u003c/span\u003e, as they are often fixed in the hardware of the mainboard, but all the others can vary.\u0026nbsp;\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003e4.2.\u0026nbsp; To keep your eyes on the prize, go back to the New Component dialog, and click the component to be taken to the Create Component dialog.\u003c/p\u003e\n\u003cp\u003eUse the input boxes to guide which pins you need to identify:\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/976/original/image.png?1759932864","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eSo in order of the dialog, we need to identify:\u003c/p\u003e\n\u003cul\u003e\n\u003cli\u003eData/Command pin for screen\u003c/li\u003e\n\u003cli\u003eReset pin for screen\u003c/li\u003e\n\u003cli\u003eChip Select pin for screen\u003c/li\u003e\n\u003cli\u003eSRAM chip select pin\u003c/li\u003e\n\u003cli\u003eBusy Pin for screen\u003c/li\u003e\n\u003c/ul\u003e\n\u003cp\u003eSimply scan through the component pinout page for the items or similar terminology.\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/978/original/acyQpNHmkF.png?1759933128","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eThose won't be our pin numbers, but using the description (and Silk Screen labels on PCB for the pins of the component) you can work out the answers.\u003c/p\u003e\n\u003cp\u003eExpect abbreviations, and don't be afraid to ask for help in the forums or discord if you are not sure.\u003c/p\u003e\n\u003cp\u003eIn this case, we may leave some of the optional pins (Busy and Reset) unselected.\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eChecking the labels on the component pinout (highlighted in images below) you can see \u003cstrong\u003eSRCS \u003c/strong\u003e(SRAM Chip Select pin) and \u003cstrong\u003eSDCS \u003c/strong\u003e(SD card CS pin - \u003cspan style=\"text-decoration: underline;\"\u003e\u003cem\u003enot used\u003c/em\u003e\u003c/span\u003e\u003cem\u003e \u003c/em\u003e), along with \u003cstrong\u003eECS \u003c/strong\u003e(E-Ink Chip Select pin) and \u003cstrong\u003eDC \u003c/strong\u003e(Data Command).\u003c/p\u003e\n\u003cp\u003eThose match up to 33, 15, 32, 14 on my feather.\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/980/original/image.png?1759933526","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/981/original/Screenshot_2025-10-08_152536.png?1759933591","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eSo plug that into the Create Component dialog, then click the create button\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/982/original/image.png?1759933706","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eThat's about it! The component registers, and then you can send it text or whatever.\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/983/original/IMG_20251008_153241_8-ezgif.com-optimize.gif?1759934118","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eNow to add the buttons it's basically identical, pick a Push Button component in the New Component dialog, then select the pin identified from your product.\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/984/original/image.png?1759934317","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eSo that lines up with 13, 12, 27 on my main board.\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/985/original/Screenshot_2025-10-08_153926.png?1759934403","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eThe usual options for button components would be: \u003cstrong\u003eOn-Change\u003c/strong\u003e rather than periodically, and Using a \u003cstrong\u003ePull-Up\u003c/strong\u003e resistor (except ESP32 boot buttons are pull down).\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/986/original/image.png?1759934546","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eNow that should be all the components configured - Stage 4 Complete!\u003c/p\u003e\n\u003cp\u003e\u0026nbsp;\u003c/p\u003e\n\u003cp\u003e5. Rejoice - You've unlocked new super powers, maybe put them to the test and go visit the \u003ca href=\"https://io.adafruit.com/actions\" target=\"_blank\"\u003eActions\u003c/a\u003e or \u003ca href=\"https://io.adafruit.com/services\" target=\"_blank\"\u003ePower-ups\u003c/a\u003e pages to explore the new world...\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/989/original/615PbjUPD9.png?1759958242","metadata":{}},{"element_type":"text","content":"\n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n  \n        \u003cp\u003eHere's a great example of using Actions on Adafruit IO to update a display using remote sensor data:\u003c/p\u003e\n      \n\n\n\n\n\n\n\n\n\n\n\n","metadata":{}},{"element_type":"guide","content":"https://learn.adafruit.com/no-code-indoor-air-quality-monitor-with-separate-display/set-up-adafruit-io-actions","metadata":{"guide_id":"4355","page_id":"30927"}},{"element_type":"text","content":"\n  \n  \n        \u003cp\u003eAnd as you've come this far, you get to see the hero image compositions by Sora (it's both a shame about the penguin instead of the logo, but equally strangely pleasing):\u003c/p\u003e\n      \n\n","metadata":{}},{"element_type":"user_image","content":"https://cdn-learn.adafruit.com/user_assets/assets/000/001/994/original/image.png?1760573742","metadata":{}}]